Hull
| Rudder Gear | Sternpost Fittings – (vertical gudgeons) | HL-2222 | 2 | |
| Rudder straps | HL-2242 | 2 | ||
| Pivot Bolt | HL-2266 | 1 | 5/16″ diameter, includes bushes (if lifting rudder used) | |
| Downhaul line cleat | HL-0095 | 1 | tube cleat (if lifting rudder) | |
| Centreboard pivot | 3/8″ diameter, with bushes | HL-2091 | 1 | Uses tufnol end plates. Comes complete with bushes check bushes |
| Keelband – assumes centreboard fitted | 3/4″ wide | HL-0702 | 15.7 | length 9′ 8″ , one 6′. Please note that for non-UK customers this may be impractical to ship |
| 1/2″ wide | HL-0701 | 12 | 2 lengths 3′ 6″ beside centreboard 2 lengths 2′ 6″ on bilge runners | |
| Rowlocks | Side Sockets | HL-0003 | 4 | |
| Rowlocks | HL-0001 | 2 | ||
| Mooring equipment | 5″ handed fairleads | HL-0147 | 2 | i.e. 2 pairs – omit if boat to be dry sailed |
| 6″ cleats | HL-1035 | 2 | suggest ash, but teak or bronze would do | |
| Buoyancy (requirements will vary with the amount of decking fitted and the type of use intended for the boat) | Small Bow bag | HL-0571 | 2 | 2 x 136 kg buoyancy – if yawl rig, HL-0570 (45kg bouyancy) may fit better in stern |
| Pillow bags – 39 x 9 | HL-0576 | 4 | 35 kg buoyancy each, fitted below side benches. Otherwise other sizes fitted under thwarts | |
| Drain Bung | Captive type | HL-0560 | 1 | or 2, one each side of keel |
Rig – Lug Yawl
| Mainsail | Mast Traveller | RG-1110 | 1 | bronze leathered |
| Head lacing -4mm | RP-0200 | 5 | ||
| Halyard sheave – 60 mm dia | RG-1501 | 1 | if fitted at all – a dumb sheave might serve just as well | |
| Halyard – 6mm braided | RP-0201 | 9 | ||
| Halyard cleat – 5″ ash | HL-1034 | 1 | or belay pin in thwart – which is also handy for keeping mast in place. 8″ x 5/8″ (HL-1050) should do. | |
| Downhaul – 6 mm braided | RP-0201 | 3 | You can’t get this too tight! | |
| Tufnol 8 mm single bow | RG-0510 | 1 | mounted on thwart | |
| Tufnol 8 mm single & becket swivel | RG-0456 | 1 | mounted on boom | |
| Belay pin 8 x 5/8″ | HL-1050 | 1 | in thwart for downhaul or use a cleat on mast | |
| Mainsheet – 10 mm braided | RP-0203 | 9 | I.O suggests 12 which seems heavy | |
| MainMainsheet boom block | RG-0524 | 1 | or 2 x singles RG-0520 | |
| Mainsheet hull block | RG-0468 | 1 | Fiddle, becket and jammer mounted on | |
| Mainsheet attachment | HL-0515 | 1 | Eyeplate mounted on aft edge of centreboard case | |
| Mizzen | Halyard – 6 mm braided | RP-0201 | 6 | probably best to use “dumb sheave” in the mast |
| Cleat – 5″ ash | HL-1034 | 1 | or belay pin HL-1050, or tube cleat HL-0096 | |
| Luff lacing – 4 mm | RP-0200 | 5 | ||
| Sheet – 6 mm | RP-0201 | 4 | length depends where you take the sheet to | |
| Sheet block – 8mm single | RG-0510 | 1 | rather than mount on rudder, could strop to sternpost | |
| Sheet cleat – camcleat | HL-0086 | 1 | mounted on side of mizzen mast? Just an idea | |
| gooseneck | RG-0025 | 1 | ? A bit elaborate – jaws would do? | |
| Downhaul block | RG-0510 | 1 | on boom – needed if jaws used instead of gooseneck | |
| Downhaul line – 6 mm | RP-0201 | 1.5 | Looped onto underside of belay pin, up to block, back down to belay pin | |
| Belay pin | HL-1050 | 1 | for downhaul line |
Rig – Gunter Sloop
| Gooseneck | RG-0027 | 1 | Mastband assembly | |
| Note: I.O. used RG- 0025 gooseneck assembly on the original boat, which was just OK – perhaps a bit light | RG-1027 | 1 | Spar end | |
| Tack and Hook fitting | RG-1830 | 1 | Tack/hook fitting if slab reefing to be used | |
| Gunter Jaws | RG-2006 | 1 | unless wooden ones are made as per the plans | |
| Have gone with the single halyard arrangement as on the plan. You may prefer a 2 halyard arrangement | Main Halyard | RP-0201 | 9 | 2 halyards (peak and throat) assumed |
| Halyard Cheek Block | RG-1474 | 1 | Mounted on side of yard | |
| Parrel beads | RG-1079 | 4 | ||
| Halyard cleat – 5″ ash | HL-1034 | 1 | teak bronze or ash | |
| Mainsheet – 10 mm braided | RP-0203 | 8 | assumes centre main with 4:1 purchase | |
| Upper mainsheet block(s) | RG-0524 | 1 | or 2 x singles RG-0520 | |
| Lower mainsheet block | RG-0468 | 1 | includes jammer. Mounted on aft edge of centreboard case if fitted, else on floor | |
| Mainsheet attachment | HL-0515 | 1 | Eyeplate mounted on aft edge of centreboard case | |
| Jibsheet – 10 mm braided | RP-0203 | 5 | ||
| Jibsheet fairleads | HL-0123 | 2 | Plenty of other options here | |
| Jibsheet Cleats | HL-0082 | 2 | ||
| Lacing | RP-0200 | 10 | for head, luff, and possibly stay lanyards | |
| Shrouds | RP-0121 | 8.8 | used 7 x 19 here for easy stowage | |
| Shroud ends | RP-0305 | 4 | ||
| Shroud plates | HL-0407 | 2 | reckon 8″ would be OK | |
| Forestay | RP-0121 | 5.2 | length varies a lot with arrangement of fore decking etc. | |
| Forestay ends | RP-0305 | 2 | ||
| Forestay fitting | HL-0508 | 1 | Screwed to inner stempost – again arrangement may need to vary | |
| Halyard Strop | RP-0120 | 0.5 | ||
| Halyard Strop Ends | RP-0304 | 2 |