Hull
Rudder Gear | Transom Fitting – upper (gudgeon) | HL-2220 | 1 | |
Transom Fitting – lower (pintle) | HL-2254 | 1 | ||
Upper rudder strap – (pintle) | HL-2242 | 1 | Plan shows fixed rudder with 2 1/8″ width cheeks – could be modified to lifting | |
Lower rudder strap – (gudgeon | HL-2212 | 1 | ||
Pivot Bolt | HL-2266 | 1 | 5/16″ diameter, includes bushes (if lifting rudder used) | |
Downhaul line cleat | HL-0095 | 1 | tube cleat (if lifting rudder) | |
Centreboard pivot | 3/8″ diameter, with bushes | HL-2090 | 1 | Uses tufnol end plates. Comes complete with bushes check bushes |
Keelband | 3/4″ wide | HL-0702 | 11 | 1 length 3′ 9″, one 7′ 3″. These lengths will vary if daggerboard is fitted. Please note that for non-UK customers this may be impractical to ship |
1/2″ wide | HL-0701 | 12 | 2 lengths 3′ each side of plate case, 2 lengths 3′ on bilge runners if fitted | |
Rowlocks | Top Sockets | HL-0002 | 4 | or side sockets HL-0003 |
Rowlocks | HL-0001 | 2 | ||
Mooring equipment | 4″ handed fairleads | HL-0146 | 1 | i.e 1 pair-omit if boat to be dry sailed |
4″ straight fairleads | HL-0156 | 2 | Mounted on transom? | |
5″ Ash cleats | HL-1034 | 2 | suggest ash, but teak or bronze would do – if fitted at all | |
Buoyancy (requirements will vary with the amount of decking fitted and the type of use intended for the boat) | Small Bow bag | HL-0570 | 1 | 45 kg buoyancy, fits forward of lug mast. If sloop rig fitted HL-0571 (136 kg buoyancy) might fit |
Pillow bag – 36 x 12 | HL-0575 | 1 | 68 kg buoyancy, fitted ahead of transom | |
Pillow bags – 24 x 7 | HL-0573 | 4 | 18 kg buoyancy each, fitted below thwarts – 2 more possible under seats if fitted | |
Drain Bung | Captive type | HL-0560 | 1 | or 2, one each side of keel |
Rig – Lug
Mainsail | Mast Traveller | RG-1110 | 1 | bronze leathered |
Head lacing -4mm | RP-0200 | 3 | ||
alyard sheave – 50 mm dia | RG-1500 | 1 | if fitted at all – a dumb sheave might serve just as well | |
Halyard – 6mm braided | RP-0201 | 7 | ||
Halyard cleat – 5″ ash | HL-1034 | 1 | or belay pin in thwart – which is also handy for keeping mast in place. 8″ x 5/8″ (HL-1050) should do. | |
Downhaul – 6 mm braided | RP-0201 | 2 | You can’t get this too tight! Leads from thwart to block on sail tack back down to belay pin | |
Tufnol 8 mm single bow | RG-0510 | 1 | mounted on sail tack | |
Belay pin 8 x 5/8″ | HL-1050 | 1 | in thwart | |
Mainsheet – 8 mm braided | RP-0202 | 5 | I.O suggests 10 which seems heavy | |
Mainsheet block | RG-0455 | 1 | on rope horse | |
Rope horse – 6mm braided | RP-0201 | 2 | fitted through knees or transom |
Rig – Gunter
Gooseneck | RG-0025 | 1 | ||
Gaff Jaws | RG-2015 | 1 | unless wooden ones are made as per the plans | |
Main Halyards – 6 mm | RP-0201 | 13 | Assuming both peak and throat halyards used | |
Halyard sheaves – 50 mm dia | RG-1500 | 2 | mounted one above the other | |
Halyard cleats – 5″ | HL-1034 | 1 | teak bronze or ash | |
Jib Halyard | RP-0201 | 6 | ||
Halyard Block | RG-0510 | 1 | on strop | |
Halyard cleat – 5″ | HL-1034 | 1 | teak bronze or ash | |
Mainsheet – 10 mm braided | RP-0202 | 6 | ||
Upper mainsheet block | RG-0520 | 1 | ||
Lower mainsheet block | RG-0521 | 1 | on rope horse | |
Rope horse – 6mm braided | RP-0201 | 2 | fitted through knees or transom | |
Jibsheet – 10 mm braided | RP-0203 | 4.5 | length varies on how you lead it | |
Jibsheet fairleads | HL-0123 | 2 | Plenty of other options here | |
Jibsheet Cleats | HL-0081 | 2 | camcleats | |
Lacing | RP-0200 | 8 | for head, luff, and possibly stay lanyards | |
Shrouds | RP-0121 | 6.6 | used 7 x 19 here for easy stowage | |
Shroud ends | RP-0305 | 4 | ||
Shroud plates | HL-0406 | 2 | reckon 6″ would be OK | |
Forestay | RP-0121 | 3.3 | ||
Forestay ends | RP-0305 | 2 | ||
Forestay fitting | HL-0421 | 1 | Bowsprit plate screwed to outer face of stem – not inner face | |
Halyard Strop | RP-0120 | 0.5 | ||
Halyard Strop Ends | RP-0304 | 2 | ||
Span | RP-0120 | 2 | ||
Span Ends | RP-0304 | 2 | ||
Span shackle | RG-0145 | 1 |